Replacing a speed sensor is easy. Want an estimate for a remanufactured transmission? Offers not valid in combination with any other discounts, promotions or items already on sale. Many people do it wrong, so here is the easy way. Primary Use: Commuting to work Everything You Need, Nothing You Don't — Great Truck! Use a wire or strong bungee cord to hold the starter's weight - do not hang from the starter wiring. I tried to jump the battery and I replaced the starter. After those attempts I had the vehicle towed to a nearby dealership who told me that coolant from the radiator leaked into the transmission and mixed fluid, damaging both the transmission and ecm.
They sent me a recall for my column steering and I had it repaired but it still is a slight hassle to change gears. What is a fair price to pay for various transmission repairs? Not valid on gift cards, special orders, installation, commercial or fleet purchases. Unless the vehicle has duel exhaust all the way back, which most do not, there is a crossover pipe that connects the left side exhaust to the right side. Remove any of the top bell housing to engine bolts that are accessible - otherwise the bolts will be removed later from underneath. Once the bolts are removed, just pull the starter out of the bell housing and push aside. Plug in any top side electrical connectors and vacuum hoses. Removing the transmission mount bolts or nuts allows the transmission to be separated from the cross member.
It had pretty good get up and go. Also, when pulling the lines out, be careful not to lose the thin metal washers. Place the U-joint bolts and hardware in an appropriately marked container. When the jack is fully lowered, carefully slide the transmission off the jack to the floor. Keeping clean fresh fluid in your transmission is the number one thing you can do to protect the transmission from premature failure.
The job of removing and replacing an automatic transmission is not tremendously difficult - it's just a matter of being prepared, being safe, and following instructions. Keeping nuts, bolts, washers, clamps, etc. Install the new filler tube O-ring that came with the rebuild kit. Learning to recognize these warning signs can save you a great deal of money and vehicle down time. For most vehicles, the speed sensor is plugged into the transmission or transaxle. When the dowel pins are in the dowel holes, install the bell housing bolts.
Torque Converter Installation Note: You must be certain the torque converter is fully seated into the transmission before installation. Tip: Use colored markers to mark connectors and hoses for easy and correct installation. If both battery cables have been disconnected, install the positive battery cable first and then the negative cable. You should feel three distinctive clicks each time the converter drops into place. Bell Housing Bolt Installation and Tightening Note: Once you have the transmission bell housing bolt holes lined up with the threaded holes in the engine block then start a couple of bolts and tighten just enough so the transmission does not slip back away from the engine block. When considering your ride's next upgrade, remember that the Nissan Xterra ignition switch needs additional attention if you want to keep your car on the road for years to come.
Now, pull the driveshaft out of the transmission and set aside. What is a transmission pressure control solenoid and how to replace one if it goes bad. Coolers are inexpensive and easy to install. Also, wrap tape around the joint caps to keep them from falling off and the pins from falling out of the caps. When disconnecting hoses and cables, make a drawing showing how each one is routed. Gas mileage sucks royally, but what would you expect from a heavy vehicle with high rolling resistance tires and the aerodynamics of a barn door? Either way, connect the starter wires at this time. Not valid on gift cards, special orders, installation, commercial or fleet purchases.
Lower the vehicle to the ground. I have had a pressure test it is holding pressure. Therefore, it is crucial that the transmission remain level or slightly titled down in the rear while being lowered to the floor. Nothing is wrong with security, battery. You may need to raise or lower the jack slightly or move it slightly to one side or the other to line up the dowels with the dowel holes. Flushing Cooler Lines Note: Flushing the oil cooler lines before installing a new or rebuilt transmission is absolutely necessary to insure the new transmission is not contaminated with debris and metal left in the lines from the old transmission. If the front of the transmission is allowed to tilt downward, the converter may slide out of the transmission and fall hard to the floor.
Also check the dowel pins on the engine and the dowel pin holes on the transmission as they also must be clean and free of burs. All of our engines are pulled from running cars in Japan. Great quiet ride, nice to drive, useful roof-rack, love the sound system. Unstoppable off-road, even without any modifications. Do the same with vacuum hoses and any other parts that might be confusing during installation.